Sustainable Building Technologies, Inc.™
Net Zero Energy Buildings™      Net Zero Energy Houses™
Sustainable Building Technologies™    Sustainable Urban Living™

The Future Belongs to the Sustainable™

Office Tel.    (81342)  71518 - 0101217        Email:  info @ sustainablebuildingsolutions .com

Reduce Your Monthly Power and Energy Expenses on your Next New Home or 
Commercial Building by 70% or More!

Home page:   www.SustainableBuildingTechnologies.com

What are Cement Sprayed Structural Insulated Panels?

At the heart of our Sustainable Building Solutions™ homes and commercial buildings are; sustainable architecture designs and our "cement-sprayed" Structural Insulated Panels ("CSSIPs").  Our CS SIPs are SUPERIOR to every other manufacturer's Structural Insulating Panels or Insulating Concrete Forms

Our cement-sprayed structural insulated panels are made in 4' x 8' panels (or custom-made in other available sizes) that are made from solid foam EPS insulation. The solid foam insulation is then "sandwiched" between two sheets of 10/14 gauge galvanized steel that are made in a vertical and horizontal pattern. Our cement-sprayed structural insulated panels have both insulating and load-bearing capabilities. The openings for the  doors and windows are cut-out and formed during construction.

Typical Structural Insulated Panels found in the market

Structural Insulated Panels (SIPs) are prefabricated insulated structural elements for use in building walls, ceilings, floors, and roofs. They provide superior and uniform insulation compared to more traditional construction methods (stud or "stick frame"), offering energy savings of 12%–14%. When installed properly, SIPs also provide a more airtight dwelling, which makes a house more comfortable and quieter.

Structural Insulated Panels not only have high R-values but also high strength-to-weight ratios. An SIP typically consists of 4- to 8-inch thick foam board insulation sandwiched between two oriented strand boards (OSB) or other structural facing materials. Manufacturers usually can customize the exterior and interior sheathing materials according to customer requirements. The facing is glued to the foam core. The panel is then either pressed or placed in a vacuum to bond the sheathing and core together.

Structural Insulated Panels can be produced in various sizes or dimensions. Some manufacturers can make panels as large as 81×281 inches (1.06×7.14 m), which require a crane to erect.

The quality of SIPs' manufacturing is very important to ensure a long life and performance. The panels must be glued, pressed, and cured properly to ensure that they don't delaminate. The panels also must have smooth surfaces and edges to prevent gaps from occurring when they're connected at the job site. Before purchasing Structural Insulated Panels, ask the manufacturer about their quality control and testing procedures. Read and compare warranties carefully.

Types of Structural Insulated Panels

The most common types of SIPs use insulation made from expanded polystyrene  (EPS) or polyisocyanurate, a polyurethane derivative. You can also find SIPs with a compressed, insulating straw core. 

Some manufacturers are examining ways of using cementitious and rigid fibrous insulating materials.

Expanded Polystyrene SIPs

The majority of Structural Insulated Panels are manufactured with expanded polystyrene (EPS) foam board or beadboard insulation. There are two types: molded expanded polystyrene (MEPS) and extruded expanded polystyrene (XEPS) foam board. This type of SIP has a nominal R-value of about 4 per inch (2.5 cm) to 5 per inch of thickness.

Standard thicknesses for either type range from 3.5 to 7.5 inches (89–190 mm) for wall panels and 5.5–11.5 inches (140–292 mm) for ceiling panels. They are available in almost any size; however, common wall panels are 41×81 inches (1.04×1.06 meters) and weigh 110 pounds (50 kilograms [kg]). 

Polyisocyanurate and Polyurethane SIPs

Some manufacturers choose to use polyisocyanurate or polyurethane as the insulating material. Foam board or liquid foam can be used to manufacture an SIP. Liquid foam can be injected between two wood skins under considerable pressure. When hardened, the foam produces a strong bond between the foam and the skins.

Polyurethane and polyisocyanurate SIPs have a nominal R-value of around R-6 to R-7 per inch (2.5 cm) of thickness. Liquid foams contain a blowing agent (an HCFC gas), some of which escapes over time, reducing the initial R-value of the SIP from about R-9 to R-7.

Wall panels made of polyisocyanurate or polyurethane are typically 3.5 (89 mm) thick. Ceiling panels are up to 7.5 inches (190 mm) thick. These panels, although more expensive, are more fire and water vapor-diffusion resistant than EPS. They also insulate 30%–40% better per given thickness.

Compressed Straw Core SIPs

Structural Insulated Panels made from straw are more environmentally friendly than the other types because they're made from renewable, recycled waste agricultural straw. However, straw Structural Insulated Panels offer less insulation per inch of thickness, and they are considerably heavier. 

Installation of Standard SIPs

Structural Insulated Panels are made in a factory and shipped to job sites. Builders then connect them together to construct a house. The speed of construction when using SIPs is much faster than other types of residential construction, especially if the builder is familiar with them. Shells can be erected quickly, saving labor time and money, without compromising quality. These savings can help compensate for the fact that SIPs usually cost more than other construction systems. 

Many SIP manufacturers also offer "panelized housing kits." The builder needs only to assemble the pre-cut pieces. Additional openings for doors and windows can be cut with standard tools at the construction site.

When installed according to manufacturers' recommendations, SIPs meet all building codes and pass the American Society for Testing and Materials (ASTM) standards of safety. In buildings constructed of SIPs, fire investigators have found that the panels held up well. For example, in one case where the structure exceeded 1,000°F (538°C) in the ceiling areas and 200°F (93°C) near the floors, most wall panels and much of the ceiling remained intact. An examination of the wall panels revealed that the foam core had neither melted nor delaminated from the skins. In similar cases, a lack of oxygen seemingly caused the fire to extinguish itself. The air supply in a structural insulated panel home can be quickly consumed in a fire.

Areas of Concern on Standard SIPs

Fire safety is a common concern about many Structural Insulated Panels - except ours! Our patented SIP technology incorporates 1 inch of concrete that is sprayed over the outside of the SIP panel, as well as the interior of the SIP panel, that encloses our SIP in concrete, making our technology virtually fireproof!  

Other SIP manufacturers may cover their exposed SIPs with a fire-rated material, such as gypsum board, which then affords some fire protection of the SIP facing and the foam, long enough to give building occupants a good measure of escape time.

Insects such as termites and rodents can become a problem for homes and commercial buildings built from ordinary SIPs - like almost any other home or commercial building. Again, however, our SIPs are encapsulated with 1 inch of concrete on the interior and exterior of our SIPs making them virtually impervious to termites, insects and rodents, unlike many other manufacturers of SIPs. This is because the foam insulation from other Structural Insulated Panel manufacturers can provide a good environment, and in fact, a "breeding ground" for these pests to dwell and multiply. 

A few cases have been noted where insects and rodents have tunneled throughout some SIPs made by other companies. 

Other SIP manufacturers have issued guidelines for preventing these problems, including the following (again, we don't require the following as we have a patented process that encapsulates our SIPs in 1 inch of concrete for the exterior and interior of our SIPs, which is applied during the construction phase)

Guidelines for many other SIP manufacturers requires applying insecticides to the structural insulated panels, as well as the following: 

Treating the ground with insecticides both before and after initial construction and backfilling 

Maintaining indoor humidity levels below 50% 

Locating outdoor plantings at least two feet (0.6 meters) away from the walls 

Trimming any over-hanging tree limbs.

Boric acid-treated insulation panels are also available. These panels keep insects away while remaining relatively harmless to humans and pets.

Also, the airtightness of a well-built SIP structure requires controlled fresh-air ventilation for safety, health, and performance, and to meet many building codes. A well-designed, installed, and properly operated mechanical ventilation system can also help prevent indoor moisture problems, which is important for achieving the energy-saving benefits of an SIP structure.

Some of the above from the Department of Energy with permission.

Cement Sprayed Structural Insulated Panels    Concentrating Solar Power

Energy Savings Guarantee    Energy Performance Contracting    FEMA Trailers    

Ground Source Heat Pumps    Insulated Concrete Forms    Insulating Concrete Forms    LEED  

Net Zero Energy Buildings   Net Zero Energy Houses    Photovoltaic Systems    

Solar Thermal Collectors    Solar Trigeneration    Structural Insulated Panels  

Structural Insulating Panels    Sustainable Building Solutions   

Sustainable Building Technologies    Sustainable Architects    Texas EcoHomes

Zero Energy Capable Homes    Zero Energy Option

Are you doing your part to stop Global Warming and Climate Change? 

Learn more about the leading causes of Global Warming and Climate Change, which are Carbon Dioxide Emissions and Greenhouse Gas Emissions at the following websites:

Carbon Dioxide Emissions
www.CarbonDioxideEmissions.com
 

Greenhouse Gas Emissions
www.GreenhouseGasEmissions.com 

Information on this website is not to be copied without the written consent of Sustainable Building Solutions

The Future Belongs to the Sustainable™

Copyright © 2005 - 2006
Sustainable Building Solutions, Inc.
All Rights Reserved